Jump to content
XPEnology Community

NoFate

Member
  • Posts

    174
  • Joined

  • Last visited

Everything posted by NoFate

  1. omg, that hack works indeed, installed : 9.1.1-10728 spk file, disabled NET, added some keys , no activation was asked! updated to latest 9.x version, and still works!
  2. Hi, since the archive from Synology is down, does anyone still have the .pat file for VirtualDSM 6.1 thnx in advance
  3. Guys , who is still using the HP gen 8 with the cougar in passtrough mode? My datastore is on a seperate SSD drive, on a seperata SATA controller, i boot esxi from the microsd Cougar is set to passtrough mode I stuggled a long time to get my disks visible, until i define it like below, but i'm still on 6.1 , mauybe time to update ALready tested the new loaders, but again, the disks on the cougar controller are gone How do you guys manage this @thecatman @koroziv esataportcfg="0x1000" usbportcfg="03000000000" internalportcfg="fffffffff"
  4. Guys , who is still using the HP gen 8 with the cougar in passtrough mode? My datastore is on a seperate SSD drive, on a seperata SATA controller, i boot esxi from the microsd Cougar is set to passtrough mode I stuggled a long time to get my disks visible, until i define it like below, but i'm still on 6.1 , mauybe time to update ALready tested the new loaders, but again, the disks on the cougar controller are gone How do you guys manage this @captainfred @R0bb0 esataportcfg="0x1000" usbportcfg="03000000000" internalportcfg="fffffffff"
  5. Hi, I mean the boatloader you are using for xpenology? Or are you not using xpenology? Mine pci slot is already taken for the extra sata card, so need another solution maybe external
  6. And is Plex using that GPU card? Does it fit on the gen 8 microserver? I have already 1 slot occuped for internal data card for SSD storage ... Don't remember anymore if there was a second... Do you run 3615 ?
  7. Hi , also running here the 1265 CPU on HP gen 8... Verry good for software transcoding, but eats a lot of electricity... Is there a way to add a GPU card ? Anyone tried to have hardware transcoding? Running 3615xs 6.1
  8. Hey @forcefullpower, did you find the cure? i am facing the same issue, running xpenology on an ESXI server, using also VMM, but the VM's itself are not getting an IP thnx
  9. Hey, just using 1 sata for the boot image, and another image for the disk, nothing special.... .SataPortMap": "2", "DiskIdxMap": "00"
  10. no, but that was indeed the trick
  11. guys, if i want to change the SN by the generator, i edit the user_config.json if i then boot up, its still te old one, what do i need todo more?
  12. Helo, i see here someone postng a script to create valid SN? does that work for quickconnect? where can i find it thnx
  13. does anyone still have that excel file?
  14. Ah, that's good So there must be somethng wrong with the 6.2.4 loader
  15. extension? where can i see that? i only see the console below?
  16. guys, is there something wrong with the 6.2.4 loader? I have an Hp Gen 8 , with esxi, the bootlader is on sata disk 0:0 , my extra hard disk is at sata disk 0:0 i have below configured : "SataPortMap": "2", "DiskIdxMap": "00" if i do this : sudo ./rploader.sh build bromolow-7.0.1-42218 i can perfect install a DSM 7 system, it works perfect had it running for a few days, during .pat upload the installed told me DSM is going to be installed on DISK 2 i do the exact same process, now with this command, a clean host in esxu sudo ./rploader.sh build bromolow-6.2.4-25556 i upload that specific pat file, again i get the message that it will install on disk 2 , it completes to 100% i do a reboot, but its back at the setup start again?? for a new .pat file upload? whats wrong? After this reboot, i'm back at point 1 what could be wrong?
  17. Who is using here an Hp Gen 8 microserver with esxi (trying 6.2.4) on sata controller 0:0 => attached the boot vmdk on sata controller 0:1 => attached the extra hard disk for DSM what should be me sataportmap and DiskIdxMap , i tried for sataportmap 1 or 2 , and diskmapid 00 , it installs the DSM fine, it completes back to 100% , but after reboot it comes back to DSM install, seems i think its always installing on the 0:0 disk?? also, if i do a change in the user json fle for the mappings, do i need run this command again? ./rploader.sh build bromolow-6.2.4-25556 thnx
  18. Guys, setting up 6.2.4 with this loader, configured sataportmap 2 running on esxi, first disk is the synoboot, second disk, is a new disk all is working fine, its booted, i can select the .pat file to upload, its installing, it completes to 100% i do a reboot, and its back in setup mode? the new hard disk is 16 GB in size, is it maybe to low? edit: also tried 50 GB as disk, didnt help either after reboot, it goes back to setup mode all going good here ....
  19. Thn for all support guys yesterday, 7 is now running on my esxi!!
  20. ok, got it,the script proposed me sataport 1 , but i changed to 2 , now it installs
  21. Hey, i'm a step further now, i gave it more cpu, and i also changed the MAC on the esxi , with the one from the file, now i can find it on the network, but when i upload the .pat file, i get this :s
  22. dont get it, did al the steps, when i reboot, i see below, looks fine normally but i cant ping it anymore, never comes online, find.synology.com isnt finding anything steps: ./rploader.sh serialgen DS3615xs now changed mac manually afterwards ./rploader.sh satamap now ./rploader.sh backup now ./rploader.sh build bromolow-7.0.1-42218 then i see below
  23. no, dont need USB indeed, its esxi gonna try again from scratch
  24. this command? ./rploader.sh satamap now yeah, i did, the usb not also this command for sn : ./rploader.sh serialgen DS3615xs now
×
×
  • Create New...