lazygatto

As I understood there is no link with valid SN/MAC for Chat notifications to work. So no any of Synology services used for that. For me notifications work well only if using local accounts of DSM. If I switch for LDAP users in Chat App - then all notifications on mobile devices gone away

Good day. Could you please tell if this loader will work with Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller? I trying to boot, but machine cannot obtain IP from router. =(

New Update from Synology today Version: 6.0.2-8451-4 Anybody test it? =)

My HP Microserver Gen8 can't boot by U-disk burned in your loader v1.01 as your indicate above. It shows "Non system disk" but works well with 5.2 XPEnoboot_DS3615xs_5.2-5644.5 from this forum. As I known, Gen8 can't boot by UEFI mode. Any suggestions? update: The U-disk above was unstable and my Gen8 was updated to DSM 6.0.2 with new U-sidk by your loader v1.01. Thanks! This DSM loader can boot in UEFI AND in legacy (BIOS) mode as well.

Updated successfully 2 VMs on eSXI and Proxmox

Нюансов особых нет. Из темы New loader берете из первого поста образ загрузчика. Для установки на голое железо разворачиваете образ на USB flash. Загружаетесь, через браузер ищете свой NAS, find.synology.com Ну и в режиме ручной установки устанавливаете pat файл последний на текущий момент (8451).

oops, good news is ata_piix works, bad news is seems not everyone loves it =) yeap. so is it possible to disable ata_piix? PS Thanks a lot for your work

Смотря куда ставить? На голую железку или в вирт. машину - от этого и инструкции будут разниться

А он в консоли так и останавливается на словах Booting the kernel. Однако по сети должен быть доступен. find.synology.com пробовали?

Появился нормальный загрузчик для DSM 6.0.2 от пользователя jun. Все подробности в этой теме в первом сообщении viewtopic.php?f=2&t=20216 Успешно установил в Proxmox VM DSM 6.0.2-8451 и следом Update 2. Ура, товарищи! =)

BTW, how can i hide my IDE drive with loader from DSM? Adding set extra_args_3615='rmmod=ata_piix' doesn't work for me =(

Finally it is working! =) VM in Proxmox running DSM 6.0.2-8451 Update 2. With loader from 1st post from jun all working like a charm. =) Thank you a lot!

I've managed to install original 8451 pat in Proxmox VM with Arcao uefi-boot img. (Mount qcow2 file as USB, Boot in UEFI from USB). No error 13. But after install I stuck on upgrade for now =)) Every time after reboot DSM shows me: We've detected that the hard drives of your current DS3615xs had been moved from a previous DS3615xs, and installing a newer DSM is required before continuing. Status: Upgrade required Firmware version: 6.0.2-8451 DSM version: 6.0.2-8451

Could you please provide more details? Your VM booting from your virtual USB device? What hypervisor do you use?

Good day, everyone Could you please help me or show in which direction i should investigate? =) I has the following problem. Trying to install DSM 6.0.2-8451 into Proxmox VM. I got jun-baremetal-uefi-arcao-v2.img, convert it into qcow2 disk. (Thanks to Arcao ) Connect it into VM, setted as UEFI boot. Xpenology booted Ok. But when I try to install DSM_DS3615xs_8451.pat I always totting error 13 - "Failed to install the file. The file is probably corrupted. (13)". Here is my grub.cfg # cat ~/xpe/grub/grub.cfg serial --port=0x3F8 --speed=115200 terminal_input serial console terminal_output serial console set default='0' set timeout='5' set fallback='0' insmod part_msdos insmod part_gpt set locale_dir=$prefix/locale set lang=en_US menuentry 'Synology DS3615xs' --class os { insmod fat set img=$prefix/../image/DS3615xs linux $img/zImage root=/dev/md0 syno_hdd_powerup_seq=0 netif_num=1 HddHotplug=0 syno_hw_version=DS3615xs vender_format_version=2 vid=0x0EA0 pid=0x2168 loglevel=0 vga=0x305 rmmod=ata_piix console=ttyS0,115200n8 sn=B2LWN08140 mac1=001132FFB5A0 withefi elevator=your_magic_elevator quiet initrd $img/ramdisk.lzma } I read that error 13 related to wrong vid/pid, but I don't really know which of them I have to use. Because VM booting from IDE. Here is VM config file # cat /etc/pve/qemu-server/111.conf bios: ovmf bootdisk: ide0 cores: 1 efidisk0: local:111/vm-111-disk-3.qcow2,size=128K ide0: local:111/vm-111-xp-uefi.qcow2 memory: 512 net0: e1000=00:11:32:FF:B5:A0,bridge=vmbr0 numa: 0 ostype: l26 sata0: local:111/vm-111-disk-2.qcow2,size=320G scsihw: virtio-scsi-pci smbios1: uuid=9d85a89b-043d-4bf8-9c9d-9955c1add4e0 sockets: 1 Would be very appreciated for any help