Jump to content
XPEnology Community

hotshots

Member
  • Posts

    84
  • Joined

  • Last visited

Posts posted by hotshots

  1. @milosv you can find here in the forum a tutorial on how to downgrade (with migration process).

    You can also just add a cheap Intel nic to your built and it should work also with your current installed loader.

    • Like 1
  2. Hy,

     

    einfacher wäre es, wenn Du Infos zu Deiner Konfiguration gegeben hättest. Aber:

    1. Ausschalten sollte nicht zu Datenverlust führen

    2. Kannst Du ein forced Install machen, was die DSM Oberfläche neu installiert - Dabei verlierst Du Deine Konfiguration, aber nicht die Daten

  3. Wenn Du eine Festplatte neu in eine DS einbaust wird sie komplett formatiert, da unter Anderem eine versteckte Partition für das System angelegt wird.

    Somit wären alle Deine Daten weg...

     

    Ich nehme an Deine externe Festplatte ist eine USB-Platte?

    Du brauchst also eine 2. Platte, die Du als Systemplatte in die 215j einbauen kannst. Dann kannst Du Deine Externe Platte wiederum als USB anschliessen und Deine Daten rüberziehen.

     

     

  4. Hy,

     

    von wo nach wo kopierst Du?

    Sind beide /Quelle und Ziel in der Fritzbox als 1GB angezeigt (Vorsicht hier gibts bei der Fritzbox irgendwo ein ECO Modus, der bremst)?

    Vorsicht, kopierst Du z.B. von einem Laptop aus via Exlorer geht alles über den Laptop, auch Quelle und Ziel direkt am Router hängen!

     

    Was kopierst Du? Bei vielen kleinen Files sinkt die Datenrate drastisch. Zum Testen solltest Du ein grosses Image nehmen (mehrer GB groß).

     

    Gruß

     

  5. Outcome of the update: SUCCESSFUL

    - DSM version prior update: DSM 6.1.4 15217 Update 5

    - Loader version and model: Jun's Loader v1.02b - DS3615xs

    - Installation type: Baremetal (see signature)

    - Additional comments: Requires reboot

  6. 1. For an update to 6.2 a new loader will be needed. This is a major release and this means high risk.

    2. If I was you I would not sell the 413j, but use it as a Backup System for the most important data

    3. Built up your new System starting with 4x 8tb in shr-1 or 5 x 8tb in shr-2

    4. Setup the new system from scratch

    5. Transfer your data from 413j to new built

    6. After new built is running use 413j as backup system ...

  7. Moin,

     

    hast Du den Stick wieder in den selben Port gesteckt?

    (ich ziehe meinen nie ab, auch damit nach evtl. Stromausfall das NAS wieder booten kann)

     

    Auf dem NAS wirst Du nach dem booten keinerlei Anzeige auf dem Monitor bekommen, das ist normal.

    Alles wird via Internet-Browser durch die DSM gesteuert. 

  8. I think you should be able to cheat the system by editing /etc.defaults/synoinfo.conf and deleting supportraidgroup="yes" and add support_syno_hybrid_raid="yes" and this should enable SHR and remove the standard raid only functions. You will have to do this every time you update the system as the new PAT files replace these defaults. This is quite clearly not supported so do at your own risk!

    The other way, if you don't want to edit config files, is to create a basic SHR array in a device that supports it and then add those discs to the array; you can then use the SHR array as normal just can't create new ones without the above work.

    • Like 1
×
×
  • Create New...