Thanks, tried the command, but eth3 still does not appear in ifconfig.
log after command:
Sep 18 11:52:39 NAS3 kernel: [ 136.337374] ixgbe: allow_unsupported_sfp Enabled
Sep 18 11:52:39 NAS3 kernel: [ 136.434260] ixgbe 0000:08:00.0: failed to load because an unsupported SFP+ or QSFP module type was detected.
Sep 18 11:52:39 NAS3 kernel: [ 136.434265] ixgbe 0000:08:00.0: Reload the driver after installing a supported module.
Sep 18 11:52:39 NAS3 kernel: [ 136.434464] ixgbe: allow_unsupported_sfp Enabled
Sep 18 11:52:39 NAS3 kernel: [ 136.518312] ixgbe 0000:08:00.1: irq 68 for MSI/MSI-X
Sep 18 11:52:39 NAS3 kernel: [ 136.518319] ixgbe 0000:08:00.1: irq 69 for MSI/MSI-X
Sep 18 11:52:39 NAS3 kernel: [ 136.518325] ixgbe 0000:08:00.1: irq 70 for MSI/MSI-X
Sep 18 11:52:39 NAS3 kernel: [ 136.518331] ixgbe 0000:08:00.1: irq 71 for MSI/MSI-X
Sep 18 11:52:39 NAS3 kernel: [ 136.518337] ixgbe 0000:08:00.1: irq 72 for MSI/MSI-X
Sep 18 11:52:39 NAS3 kernel: [ 136.519256] ixgbe 0000:08:00.1: PCI Express bandwidth of 16GT/s available
Sep 18 11:52:39 NAS3 kernel: [ 136.519259] ixgbe 0000:08:00.1: (Speed:2.5GT/s, Width: x8, Encoding Loss:20%)
Sep 18 11:52:39 NAS3 kernel: [ 136.519333] ixgbe 0000:08:00.1 eth2: MAC: 1, PHY: 10, PBA No: E37002-011
Sep 18 11:52:39 NAS3 kernel: [ 136.519336] ixgbe 0000:08:00.1: 00:1b:21:d9:29:7e
Sep 18 11:52:39 NAS3 kernel: [ 136.519339] ixgbe 0000:08:00.1 eth2: Enabled Features: RxQ: 4 TxQ: 4
Sep 18 11:52:39 NAS3 kernel: [ 136.519342] ixgbe 0000:08:00.1 eth2: Intel® 10 Gigabit Network Connection
ifconfig:
NAS3> ifconfig
eth0 Link encap:Ethernet HWaddr 00:15:17:E1:F3:C0
inet addr:10.0.40.17 Bcast:10.0.40.255 Mask:255.255.255.0
inet6 addr: fe80::215:17ff:fee1:f3c0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:213997 errors:0 dropped:0 overruns:0 frame:0
TX packets:140469 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:275330815 (262.5 MiB) TX bytes:11032083 (10.5 MiB)
Interrupt:18 Memory:b8820000-b8840000
eth1 Link encap:Ethernet HWaddr 00:15:17:E1:F3:C1
inet addr:10.0.40.18 Bcast:10.0.255.255 Mask:255.255.0.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:19 Memory:b8800000-b8820000
eth2 Link encap:Ethernet HWaddr 00:1B:21:D9:29:7E
inet addr:10.0.80.3 Bcast:10.0.80.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:934 errors:0 dropped:0 overruns:0 frame:0
TX packets:934 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:127579 (124.5 KiB) TX bytes:127579 (124.5 KiB)
Could I add the command in syslinux.cfg in xenoboot ?
btw I'm using DSM 5.2-5967