leonjehae

anyone ever tried the High Availability option? can't get it working, everytime i connect the heartbeat cable both systems are "looping".(2xN54L) best regards, Leon

You even get it hot pluggable afterwards best regards, Leon

Hi Trantor, I have read almost the whole board but no one seems to use SHA? Since you are one of the best Xpenology specialist as far as i can see, i ask you directly if i may. Done everything as it supposed to (in synology SHA manual) but everytime when i connect the heartbeatcable both (N54L) become inaccessable. Both systems have the same (intel pro1000) Nic's, same harddisks on same slots,Ipv6 is disabled just like DHCP and PPPoe is not connected.(cannot find where to disable that)......... Do you have any suggestions? (Of course i use different serial numbers and the real hardware macaddresses of al the 4 NIC's.(edited in the vender file) Best regards, Leon

Changed everything like it should and everything is working to except SHA, have you tried that already? Everytime when i connect the heartbeat cable both systems are inaccessable. Best regards, Leon

You must change it in the vender file

Did al that and everything is working as it should.........except SHA..........every time i connect the heartbeat cable both systems are inaccessable. anyone tried SHA? My serials are correct, both NICS en harddisk are exactly the same, eveything is as the procedure but stil, the heartbeat isn't connected properly......of course, all nic's are working in "normal" function. Any help is welcome

Just simply type /var/dmesg >readme and then read the readme file. Dmesg outputs kernelmessages so you can find the real Macaddress. (Search for Mac for example with the vi-editor) Best regards, Leon

Had the same, see elswhere my solution(modded Bios worked) Best regards, Leon

The only thing you have to do in my humble opinion is to find the REAL (hardware) MAC-adres and then every WOL-command wil work. (If in BIOS enabled and the NIC support it)........................the only trick is HOW to find the REAL MAC-adres?................................well, you can find it trough : /var/dmesg (via putty/SSH of course) For example write it to : /var/dmesg >readme then open the file readme for example with the VI-editor and search for "mac" (/mac ) and you will find the real Mac-adres. something like : 4.670955] tg3 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 4.671048] tg3 0000:02:00.0: setting latency timer to 64 [ 4.722294] pcieport 0000:00:06.0: eth0: Tigon3 [partno(BCM95723) rev 5784100] (PCI Express) MAC address 38:ba:ae:a0:fe:d8 [ 4.722378] pcieport 0000:00:06.0: eth0: attached PHY is 5784 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0]) [ 4.722421] pcieport 0000:00:06.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 4.722462] pcieport 0000:00:06.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit] [ 4.732906] bromolow_synobios: module license 'Synology Inc.' taints kernel. Write down the MAC-adres, then quit the VI-editor (:q!) The output of dmesg is a list of kernelmessages so................. Best regards, Léon To get a 10 you could also change the MAC-adres in the Vender file (with a HEX-editor) so that even the DSM-software will output the wright MAC.

Thnx, here the same now but has modded the Bios for it while on DSM4,2 it also worked without modding? I got 5 disks (each 4TB), listed as Disk 1, 2, 3, 4 and 6 in System Information under Storage. 4 disks in the "hot-plug able" bays and one disk in the DVD bay. The disk in the DVD bay is connected to the internal SATA port.

Moetschjos Graatsiais

Does your router support Gigabit? I used my N54L with a 100Mbit router before and that caused such limitations. It appears even when you use an incorrect networkcabel, use min. Cat5e

Can anyone explain how the search option within this board works? Every search ends in no result? Thnx, Leon

How many Drives you use? DSM isn't recognize my fifth drive anymore (In DVD-bay) Leon

Do you have tested it also with five harddrives? (one in the DVD-bay?) It worked with DSM 4.2 but now with DSM4.3 the fifth drive isn't detected anymore, even after reinstalling everything. Even tried every possibility in the BIOS (AHCI,RAID,EDI) The drive is detected by the Microserver but not within DSM. You use 4 or more drivers?

Just make a simple script with the VI-editor and put it in : /usr/syno/etc/rc.d From there every scripts runs automaticaly when the server boots. The script should read : ifconfig eth0 hw ether 00:11:22:33:44:55 ifconfig eth1 hw ether 00:11:22:33:44:56 Where eth0 is your first NIC, eth1 your second and so on. PS. Of course you do as above with for example putty (SSH) Best regards, Léon

Just update to DSM 4.3 b3810 and after that the fifth harddrive isn't recognized anymore by DSM? With DSM 4.2 everything worked fine, i use an HP Proliant Microserver N54L with 4GB and 5x1,5 TB drive's 4 installed through the RAID controller (Hardware RAID not active on Bios) en 1 installed in the DVD-drive bay. The one in the DVD-drive bay was recognized before with DSM 4.2 and i had a RAID5 configuration with it. (So 5 drives with 6TB eff) Now DSM only finds 4 harddrives while the Bios of the N54L recognizes them all? Rebooted, deleting the volume. nothing works to find the fifth drive in DSM 4.3 Any ideas? Best regards, Léon