Leaderboard

there seems to be a new ASMedia SATA chip comparable to the JMB585 (pcie 3.0 2x, 5 port sata) ASMedia ASM1166, with pcie 3.0 2x support and 6 stata ports, seems to be a alternative to the jmb585 and the one additional port could come in handy when using a 6 x sata onboard solution and wanting to have 12 sata ports and only using one pcie 4x slot, there are also versions as pcie 1x - best option for a pcie 1x slot atm as it can utilize the pcie 3.0 and get up to 1000 MB/s with the one pcie lane (have'nt seen a jmb585 as pcie 1x card), better then any marvell 88se9215 (sadly no real use for apollolake/geminilake systems as they only support pcie 2.0 but the new elkhart lake J6413 scheduled for q1/2021 will have pcie 3.0 support and will have two more pcie lanes) pcie 4x cards (only 2 lanes are used), i ordered one of these https://www.amazon.com/BEYIMEI-Controller-Expansion-Non-Raid-Standard/dp/B08DFK4LZ7 https://www.amazon.com/MZHOU-Controller-Converter-%EF%BC%88Support-Devices%EF%BC%89 pcie 1x cards https://www.amazon.de/ASM1166-GEN3-Erweiterungskarte-langlebige-Play-Erweiterungskarte-PCI-E4X8X16X-Schnittstelle/dp/B08KT9FJZC https://www.amazon.de/awstroe-GEN3-Erweiterungskarte-Erweiterungskarte-Temperaturwiderstand-PCI-E4X8X16X-Schnittstelle-Default/dp/B08KTCQ6VD https://www.amazon.de/Erweiterungskarte-ASMedia-Festplatte-Schnittstelle-Durable/dp/B08L6JLZ2V as i still wanted to use my M.2 slot for sata ports or 10G nic i was looking for mechanical meaningful solutions (the M.2 card i bought with a pcie 4x slot on it was not really usable as it had to much mechanical problems) there are riser adapter for M.2 to a normal pcie slot (that can be bolted or glued some where and things like cpu cooler or pcie slots will be no hindrance) using a M.2 slot as normal PCIe 3.0 4x Slot with as riser (i ordered the adt-link adapter) https://www.amazon.com/ADT-LINK-Extension-Express-Extender-R42SF/dp/B08DRDT47K https://www.amazon.com/NGFF-Extension-Cable-90%C2%B0Right-Angle/dp/B08B3KGNHC https://www.amazon.com/Timack-NGFF-NVMe-Extension-Cable/dp/B08BXNGKGH same as above but with a 16x pcie slot (imho not needed as the adapters from above have a open back pcie 4x slot so a 8x/16x card will fit in) https://www.amazon.com/pcie-NGFF-NVMe-Extension-Cable/dp/B08B3PRJGG https://www.amazon.com/Extension-Cable-Extender-Cablem-2-Extension/dp/B08B3HRG7L

When setting up an XPEnology system, you must first select a DSM platform and version. XPEnology supports a few specific DSM platforms that enable certain hardware and software features. All support a minimum of 4 CPU cores, 64GB of RAM, 10Gbe network cards and 12-disk arrays. When you choose a platform and the desired DSM software version, you must download the correct corresponding loader. That may not be the "newest" loader available. The last 6.x version (6.2.4-25556) is functional only with the TCRP loader. TCRP is very different than the Jun loader. If you want to learn more, or if you are interested in deploying the latest 7.x versions, see the 7.x Loaders and Platforms thread. Be advised that installing 6.2.4 with TCRP is basically the same procedure as installing 7.x. Each of these combinations can be run "baremetal" as a stand-alone operating system OR as a virtual machine within a hypervisor (VMWare ESXi is most popular and best documented, but other hypervisors can be used if desired). Review the table and decision tree below to help you navigate the options. 6.x Loaders and Platforms as of 16-May-2022 Options Ranked DSM Platform DSM Version Loader Boot Methods*** Hardware Transcode Support NVMe Cache Support RAIDF1 Support Oldest CPU Supported Max CPU Threads Notes 1,3a DS918+ 6.2.0 to 6.2.3-25426 Jun 1.04b UEFI, BIOS/CSM Yes Yes No Haswell ** 8 6.2.0, 6.2.3 ok, 6.2.1/6.2.2 not recommended for new installs* 2,3b DS3617xs 6.2.0 to 6.2.3-25426 Jun 1.03b BIOS/CSM only No No Yes any x86-64 16 6.2.0, 6.2.3 ok, 6.2.1/6.2.2 not recommended for new installs* DS3615xs 6.2.0 to 6.2.3-25426 Jun 1.03b BIOS/CSM only No No Yes any x86-64 8 6.2.0, 6.2.3 ok, 6.2.1/6.2.2 not recommended for new installs* DS918+ 6.2.4-25556 TCRP 0.4.6 UEFI, BIOS/CSM Yes Yes No Haswell ** 8 recommend 7.x instead DS3615xs 6.2.4-25556 TCRP 0.4.6 UEFI, BIOS/CSM No No Yes any x86-64 8 recommend 7.x instead DS916+ 6.0.3 to 6.1.7 Jun 1.02b UEFI, BIOS/CSM Yes No No Haswell ** 8 obsolete, use DS918+ instead DS3617xs 6.0.3 to 6.1.6 Jun 1.02b UEFI, BIOS/CSM No No Yes any x86-64 16 6.1.7 may kernel panic on ESXi 4 DS3615xs 6.0.3 to 6.1.7 Jun 1.02b UEFI, BIOS/CSM No No Yes any x86-64 8 best compatibility on 6.1.x * 6.2.1 and 6.2.2 have a unique kernel signature causing issues with most kernel driver modules, including those included in the loader. Hardware compatibility is limited. ** FMA3 instruction support required. All Haswell Core processors or later support it. Only a select few Pentium, and no Celeron CPUs do. ** Piledriver is believed to be the minimum AMD CPU architecture to support the DS916+ and DS918+ DSM platforms. *** If you need an MBR version of the boot loader because your system does not support a modern boot methodology, follow this procedure. CURRENT LOADER/PLATFORM RECOMMENDATIONS/SAMPLE DECISION POINTS: 1. DEFAULT install DS918+ 6.2.3 - also if hardware transcoding or NVMe cache support is desired, or if your system only support UEFI boot Prerequisite: Intel Haswell (aka 4th generation) or newer CPU architecture (or AMD equivalent) Configuration: baremetal loader 1.04b, DSM platform DS918+ version 6.2.3 Compatibility troubleshooting options: extra.lzma or ESXi 2. ALTERNATE install DS3617xs 6.2.3 - if RAIDF1, 16-thread or best SAS support is desired, or your CPU is too old for DS918+ Prerequisite: USB key boot mode must be set to BIOS/CSM/Legacy Boot Configuration: baremetal loader 1.03b, DSM platform DS3617xs version 6.2.3 Compatibility troubleshooting options: extra.lzma, DS3615xs platform, or ESXi 3. ESXi (or other hypervisor) virtual machine install - generally, if hardware is unsupported by DSM but works with a hypervisor Prerequisites: ESXi hardware compatibility, free or full ESXi 6.x or 7.x license Use case examples: virtualize unsupported NIC, virtualize SAS/NVMe disks and present as SATA, run other ESXi VM's instead of Synology VMM Option 3a: 1.04b loader, DSM platform DS918+ version 6.2.3 Option 3b: 1.03b loader, DSM platform DS3617xs version 6.2.3 (VM must be set to BIOS Firmware) Preferred configurations: passthrough SATA controller and disks, and/or configure RDM/RAW disks 4. FALLBACK install DS3615xs 6.1.7 - if you can't get anything else to work Prerequisite: none Configuration: baremetal loader 1.02b, DSM platform DS3615xs version 6.1.7 SPECIAL NOTE for Intel 8th generation+ (Coffee Lake, Comet Lake, Ice Lake, etc.) motherboards with embedded Intel network controllers: Each time Intel releases a new chipset, it updates the PCI id for the embedded NIC. This means there is a driver update required to support it, which may or may not be available with an extra.lzma update. Alternatively, disable the onboard NIC and install a compatible PCIe NIC such as the Intel CT gigabit card.

Вот держите. https://mega.nz/file/qI8UHISa#_x5yBVmXMPvWzTd9phOWQ0uMLPYD6VSEAW0NnaNtjrI

IM SO SORRY!! Disabled C1 and worked!

like he did? https://www.youtube.com/watch?v=FTplfOyxHcU https://www.youtube.com/watch?v=1T7h2X5xpE8 https://www.youtube.com/watch?v=eMGLsrkrBeU https://www.youtube.com/watch?v=LHksdTTGBbE and final: (he gave up) https://www.youtube.com/embed/z0hCKfceYmc?start=982 if you aim for such high drive count maybe go with freenas, unraid or omv, if you really want to try it with xpenology test with quicknicks loader if its really solving the problem and if so look deeper into the loader like i suggested here: https://xpenology.com/forum/topic/28321-driver-extension-jun-103b104b-for-dsm623-for-918-3615xs-3617xs/?do=findComment&comment=159301 https://xpenology.com/forum/topic/8057-physical-drive-limits-of-an-emulated-synology-machine/page/4/?tab=comments#comment-167748 as seen in the threads i linked above, its seems to be more then just changing maxdisks and internaldrives in synoinfo.conf (what you already tried)

thats ahci and working in 6.x without any added drivers, its build into the kernel you will not get anything like console output on the monitor, the local console is switched to serial port, grab a 0-modem cable and putty if you can you might start to read the faq and tutorial section, there are lots of changes in 6.x compared with 5.2 especially min. cpu support for 918+ and csm/legacy requirement (no uefi) for 3615/17 (csm setting in bios and choosing the non uefi usb boot device) https://xpenology.com/forum/forum/83-faq-start-here/ https://xpenology.com/forum/topic/13333-tutorialreference-6x-loaders-and-platforms/ please don't assume anything like a driver issue as long as you cant prove the point, misleading for you and for other trying to help you also its kind of weird to expect we know hat hardware, loader and dsm type you used, you need to tell

After connect disks to the live Debian distro, I run command fsck.ext4 -fyv /dev/md/2 Tool repair my Volume and now I can connect to the desktop Thansk for all

Да всё очень просто..... Скачать файл для своей версии DSM по ссылке выше, если он у вас не появился во вкладке обновления. Далее..., в Панели управления, во Вкладке обновление, выбрать Обновление вручную. Подсунуть файл и обновиться. И всё...... И не забывайте , перед обновлением, делать Резервную копию настроек, это там же, во вкладке Резервирование

Hi IG-88 i added your driver files to my usb stick and rebooted and it worked first time thanks very much for that.

А матери конечно с вафельными картами у нас конечно отменили или не существуют в продажах как класс? Для всех остальных! XPEnology используется как сервер видеонаблюдения (Surveillance Station) и ТОЛЬКО! Ethernet используется для связи XPEnology с АЦП GrandStream (преобразует аналоговый сигнал с камер в цифру) Wi-Fi подключение используется для доступа к web-морде видеонаблюдения для настройки, раз в месяц контроля, максимум для слива файлов (такого еще не было за 5 месяцев использования). Основная связь с Surveillance Station по уведомлениям отправляемым им.

Извините, но ваш пост даже комментировать не хочется! Вы не обсуждаете проблему, вы обсираете выбор людей!

Не поймете чем лучше, если вы полагаете что xpenology используется в качестве роутера wifi модуль используется для уменьшения количества проводов, связи с сеткой и скрытой установки, и да, скорости связи достаточно для выполняемых им функций

Очень хорошо что вы не пользуетесь данными функциями, но это совсем не значит этими возможностями не пользуются другие, у меня есть xpenology на 4.2 и там изумительно работает wifi-модуль, и мне очень его не хватает на 4.3 Поэтому я поддерживаю автора топика о наличии проблемы с wifi модулями Могу предоставить скрины если надо.