Leaderboard

Hi, I've made new release, VirtualBox is updated to 5.2.20. I've created packages for few more architectures, you can find them now in release page on github, I've tested only bromolow package. Also note that currently there is a bug with upgrade procedure so you will have to uninstall old version and then install new one. Regards, Seba

nah the actual MAC works fine. There seems to be some unwritten rule that the serial and MAC needs to match but it doesn't. Even with activating the hardware transcoding - as long as the serial is legit, it'll work regardless of the MAC address used. On this same board and the 3615 loader, I couldn't get the LAN to work unless i used the actual MAC address. The 918+ loader worked with whatever i put in there. as i mentioned before - the serial cable is a must for troubleshooting these loaders. you'll see whats happening and hopefully figure out whats going on. without it - we're all guessing.

Ahhh.. Pretty sure you shouldn't use the MAC address of the board. I thought you needed to use something as per a mac and serial number generator - as Synology use a particular range of MAC Addresses. Use loader 1.03b My grub.cfg for the DS3617xs on this board 'had'... set sn=1690ODN068xxx set mac1=001132552xxx Finish off the serial number and MAC yourself - replacing the serial XXX with a number and the mac1 XXX with a hex-number.. Check your VID and PID again of your USB drive and then change them to suit.. change 'SataportMap' to equal 4 (in grub.cfg).. BIOS There are definitely some things you need to change in the BIOS and - as mentioned - you MUST boot to Legacy USB (NOT UEFI).... You also need to enable CSM and set the USB to legacy. Dont change Video to legacy or you'll probably get a black screen and need to use your CMOS reset jumper! Also Disable C-States. I havent tried DS3615 on this board.. NIC Also, try another NIC, if you have one.. if you dont, you can pick up a single port card for about £10 (ex-corporate) on Ebay.. Dual port NICs come in about £25 Make sure you buy intel nics .. Definitely try using another network cable and another port on your switch.. Rather than using the Find synology utility, use a network scanner and look for the MAC address you set above.. Then you'll know for sure..

I did it a few days ago. I tested that I had a configuration that worked using a spare disk. Then I installed all the drives from my Synology, and I got the option to migrate. I did that, and it worked.

4 версия установилась и запускалась, но сразу падала. 5ю версию не ставьте, это скорее вирус=) Пришлось форматировать винчестеры. Ну это я все к чему... я нашел новую 6 версию 2018 года!😀 Добавляю ее во вложении. Добавляю ссылку на инструкцию для synology на сайте plex: https://forums.plex.tv/t/plexconnect-on-synology/37134 Все работает супер. 1080p в отличном качестве без тормозов! plexconnect_v0.6-1_for_dsm6.spk

Ребят, кончайте флудить, создайте тему и не засоряйте основной топик, пжта, это просьба ради уважения к тем, кто подписался на тему, возможно они ждут ответа на свой вопрос, а вынуждены читать вашу переписку. Боагодарю, если поняли мой позыв и прошу не цитировать и не отвечать.

Я чёт думал что вы копируете с компа/на комп, подключенный к роутеру на/с внешнего винта, подключенного к серверу. Если просто с винта на сервер - смотрите в сторону кармана для винта. Попробуйте достать оттуда диск, и проверить копирование напрямую, подключив его к сата порту. пс: вангую что корпус для винта самый дешман, и просто не вывозит скорость. Напишите модель корпуса.

https://xpenology.com/forum/topic/13030-dsm-5x6x-cpu-name-cores-infomation-change-tool/