R&R Posted July 7, 2015 Share #1 Posted July 7, 2015 Hi all, Yesterday i was tinkering with my xpenology because my wifi didn't work (still doesn't work btw). Anyway i had a Highpoint rocketraid 620 laying around doing nothing, so tried it in the xpenology machine and lo and behold it didn't work. Well to make a long story short i found this website:https://blog.hqcodeshop.fi/archives/266-HighPoint-RocketRAID-620-Linux-driver.html and searched for some information about cross-compiling, and what do you know, it seems to work with dsm 5.2-5565. You can download the .ko file right here -->http://1drv.ms/1NOtZTi, i also cross-compiled the modules for the 64x and 27x0 series card just for fun(didn't test them). dsemg output: [11229.271220] rr62x:RocketRAID 62x SATA controller driver v1.2 (Jul 1 2012) [11229.909550] ACPI Warning: For \_SB_.PCI0._PRT: Missing expected return value (20130328/nsrepair-216) [11229.909823] ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16 [11229.909891] rr62x:adapter at PCI 2:0:0, IRQ 16 [11229.912006] rr62x:[0 0 ] start port. [11229.912006] rr62x:[0 0 ] start port hard reset (probe 1). [11229.912006] rr62x:[0 1 ] start port. [11229.912006] rr62x:[0 1 ] start port hard reset (probe 1). [11232.868064] rr62x:[0 0 ] failed to hard reset. [11232.868076] rr62x:[0 0 ] failed to perform port hard reset. [11233.060006] rr62x:[0 1 ] start port soft reset (probe 1). [11233.715161] rr62x:[0 1 ] port started successfully. [11233.715161] rr62x:[0 1 0] device probed successfully. [11233.777078] scsi5 : rr62x [11233.778143] scsi 5:0:0:0: Direct-Access WDC WD2500AAJS-2 12.0 PQ: 0 ANSI: 5 [11233.778457] sd 5:0:0:0: Attached scsi generic sg2 type 0 [11233.778777] sd 5:0:0:0: [sdf] 488397168 512-byte logical blocks: (250 GB/232 GiB) [11233.778831] sd 5:0:0:0: [sdf] Write Protect is off [11233.778836] sd 5:0:0:0: [sdf] Mode Sense: 2f 00 00 00 [11233.778872] sd 5:0:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [11233.786121] sdf: sdf1 sdf2 sdf3 < sdf5 > [11233.787058] sd 5:0:0:0: [sdf] Attached SCSI disk Don't execly know what "failed to hard reset" and "failed to perform port hard reset" is all about. At this point i can't get it to load at boot. So for now its not practical but at least its a start. R&R signing off. source for 64x http://www.highpoint-tech.com/USA_new/series_rr600-download.htm source for 27x0 http://www.highpoint-tech.com/USA_new/series_rr272x_configuration.htm Link to comment Share on other sites More sharing options...
brantje Posted July 7, 2015 Share #2 Posted July 7, 2015 You got a link where we can buy those cards Link to comment Share on other sites More sharing options...
R&R Posted July 7, 2015 Author Share #3 Posted July 7, 2015 I got my Highpoint from Ebay. Worldwide i suppose Ebay will be a good source. But there will be plenty of other hardware shops in each and every country that will sell you a RAID card. http://www.ebay.com Link to comment Share on other sites More sharing options...
Thecapri Posted July 8, 2015 Share #4 Posted July 8, 2015 hello , i did have the same problem with the rocketraid i found other cart that work without modify anything see here see post here Link to comment Share on other sites More sharing options...
Emmer Posted October 4, 2015 Share #5 Posted October 4, 2015 Hi all, Yesterday i was tinkering with my xpenology because my wifi didn't work (still doesn't work btw). Anyway i had a Highpoint rocketraid 620 laying around doing nothing, so tried it in the xpenology machine and lo and behold it didn't work. Well to make a long story short i found this website:https://blog.hqcodeshop.fi/archives/266-HighPoint-RocketRAID-620-Linux-driver.html and searched for some information about cross-compiling, and what do you know, it seems to work with dsm 5.2-5565. You can download the .ko file right here -->http://1drv.ms/1NOtZTi, i also cross-compiled the modules for the 64x and 27x0 series card just for fun(didn't test them). Hi @R&R, I've been trying to get the driver for rr2680 compiled but it's getting very frustrating, do you have any tips on how to go about it? the things come in sort of packed automatic installer files. i get the drivers out, but when i try to crosscompile with the right toolchain, and the right kerneldir it just does nothing when you press enter. compiling it against the running kernel works just fine. Any help would be very much apreciated Link to comment Share on other sites More sharing options...
Trantor Posted October 4, 2015 Share #6 Posted October 4, 2015 Look here for 2680 : viewtopic.php?f=2&t=1361&start=620#p45107 Here for 271x/272x : viewtopic.php?f=2&t=1361&hilit=rocketraid&start=580#p42804 Here for 620/622/640/644/640L/642L/644L/RR644LS : viewtopic.php?f=2&t=7737&p=43301&hilit=rocketraid#p43301 Link to comment Share on other sites More sharing options...
Recommended Posts