aleksey_z Posted February 18, 2017 Share #1 Posted February 18, 2017 Good day. I read about it https://forum.synology.com/enu/viewtopi ... ps#p449794 and try to connect my old UPS. Prompt me please, can I connect the my old UPS Mustek 600Plus only with RS232 interface to my syno ds3615. I have usb-serial adapter STLabs U-350 and installed drivers: [ 26.591680] usbcore: registered new interface driver usbserial [ 26.605321] usbcore: registered new interface driver ftdi_sio [ 26.605330] usbserial: USB Serial support registered for FTDI USB Serial Device [ 26.644318] usbcore: registered new interface driver cp210x [ 26.644327] usbserial: USB Serial support registered for cp210x [ 26.645183] usbcore: registered new interface driver pl2303 [ 26.645191] usbserial: USB Serial support registered for pl2303 [ 26.645201] pl2303 2-1.8:1.0: pl2303 converter detected [ 26.646771] usb 2-1.8: pl2303 converter now attached to ttyUSB0 [ 26.662390] usbcore: registered new interface driver ch341 [ 26.662400] usbserial: USB Serial support registered for ch341-uart [ 26.684289] usbcore: registered new interface driver ti_usb_3410_5052 [ 26.684302] usbserial: USB Serial support registered for TI USB 3410 1 port adapter [ 26.684310] usbserial: USB Serial support registered for TI USB 5052 2 port adapter I have tried to make changes to the file /usr/syno/etc/ups/ups.conf as: driver = blazer_usb port = /dev/ttyUSB0 and driver = blazer_usb port = /dev/ttyUSB0 cable = 940-0024C But nothing happens, the UPS is not seen in the DSM. What am I doing wrong? Thanks. Quote Link to comment Share on other sites More sharing options...
aleksey_z Posted February 18, 2017 Author Share #2 Posted February 18, 2017 log: [spoiler=] /usr/syno/etc/rc.sysv$ sh ups-usb.sh restart ups-usb.sh restart invoked. Stop UPS Daemon Can't open /var/state/ups/richcomm_usb-ttyUSB0.pid: No such file or directory Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 No supported devices found. Please check your device availability with 'lsusb' and make sure you have an up-to-date version of NUT. If this does not help, try running the driver with at least 'subdriver', 'vendorid' and 'productid' options specified. Please refer to the man page for details about these options (man 8 blazer_usb). Network UPS Tools - Megatec/Q1 protocol USB driver 0.11 (SDS6-0-8445-factory-repack-8445-160817) Driver failed to start (exit status=1) No matching HID UPS found Driver failed to start (exit status=1) Fatal error: unusable configuration Driver failed to start (exit status=1) Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Network UPS Tools - Generic HID driver 0.38 (SDS6-0-8445-factory-repack-8445-160817) USB communication driver 0.32 Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Network UPS Tools - BCMXCP UPS driver 0.28 (SDS6-0-8445-factory-repack-8445-160817) USB communication subdriver 0.22 Unable to find POWERWARE UPS device on USB bus (USB) Things to try: - Connect UPS device to USB bus - Run this driver as another user (upsdrvctl -u or 'user=...' in ups.conf). See upsdrvctl(8) and ups.conf(5). Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Startup timer elapsed, continuing... Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 No matching USB/HID UPS found Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20 (SDS6-0-8445-factory-repack-8445-160817) Warning: This is an experimental driver. Some features may not function correctly. Driver failed to start (exit status=1) Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 This UPS is not supported. product=[], cmd=[] Communications with UPS lost: Can't open USB device, retrying ... No supported devices found. Please check your device availability with 'lsusb' and make sure you have an up-to-date version of NUT. If this does not help, try running the driver with at least 'subdriver', 'vendorid' and 'productid' options specified. Please refer to the man page for details about these options (man 8 blazer_usb). Network UPS Tools - Megatec/Q1 protocol USB driver 0.11 (SDS6-0-8445-factory-repack-8445-160817) Driver failed to start (exit status=1) No matching HID UPS found Driver failed to start (exit status=1) Fatal error: unusable configuration Driver failed to start (exit status=1) Duplicate driver instance detected! Terminating other driver! Unable to find Richcomm dry-contact to USB solution Things to try: - Connect UPS device to USB bus - Run this driver as another user (upsdrvctl -u or 'user=...' in ups.conf). See upsdrvctl(8) and ups.conf(5). Fatal error: unusable configuration Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Network UPS Tools - Generic HID driver 0.38 (SDS6-0-8445-factory-repack-8445-160817) USB communication driver 0.32 Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Network UPS Tools - BCMXCP UPS driver 0.28 (SDS6-0-8445-factory-repack-8445-160817) USB communication subdriver 0.22 Unable to find POWERWARE UPS device on USB bus (USB) Things to try: - Connect UPS device to USB bus - Run this driver as another user (upsdrvctl -u or 'user=...' in ups.conf). See upsdrvctl(8) and ups.conf(5). Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Network UPS Tools - Richcomm dry-contact to USB driver 0.04 (SDS6-0-8445-factory-repack-8445-160817) Warning: This is an experimental driver. Some features may not function correctly. Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Startup timer elapsed, continuing... Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 No matching USB/HID UPS found Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20 (SDS6-0-8445-factory-repack-8445-160817) Warning: This is an experimental driver. Some features may not function correctly. Driver failed to start (exit status=1) Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 This UPS is not supported. product=[], cmd=[] Communications with UPS lost: Can't open USB device, retrying ... No supported devices found. Please check your device availability with 'lsusb' and make sure you have an up-to-date version of NUT. If this does not help, try running the driver with at least 'subdriver', 'vendorid' and 'productid' options specified. Please refer to the man page for details about these options (man 8 blazer_usb). Network UPS Tools - Megatec/Q1 protocol USB driver 0.11 (SDS6-0-8445-factory-repack-8445-160817) Driver failed to start (exit status=1) No matching HID UPS found Driver failed to start (exit status=1) Fatal error: unusable configuration Driver failed to start (exit status=1) Duplicate driver instance detected! Terminating other driver! Unable to find Richcomm dry-contact to USB solution Things to try: - Connect UPS device to USB bus - Run this driver as another user (upsdrvctl -u or 'user=...' in ups.conf). See upsdrvctl(8) and ups.conf(5). Fatal error: unusable configuration Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Network UPS Tools - Generic HID driver 0.38 (SDS6-0-8445-factory-repack-8445-160817) USB communication driver 0.32 Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Network UPS Tools - BCMXCP UPS driver 0.28 (SDS6-0-8445-factory-repack-8445-160817) USB communication subdriver 0.22 Unable to find POWERWARE UPS device on USB bus (USB) Things to try: - Connect UPS device to USB bus - Run this driver as another user (upsdrvctl -u or 'user=...' in ups.conf). See upsdrvctl(8) and ups.conf(5). Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Network UPS Tools - Richcomm dry-contact to USB driver 0.04 (SDS6-0-8445-factory-repack-8445-160817) Warning: This is an experimental driver. Some features may not function correctly. Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Communications with UPS lost: Can't open USB device, retrying ... Startup timer elapsed, continuing... Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 No matching USB/HID UPS found Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20 (SDS6-0-8445-factory-repack-8445-160817) Warning: This is an experimental driver. Some features may not function correctly. Driver failed to start (exit status=1) Communications with UPS lost: Can't open USB device, retrying ... Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 This UPS is not supported. product=[], cmd=[] P.S. if i in setting: [PowerMust] driver = blazer_usb port = /dev/ttyUSB0 desc = "Mustek PowerMust 600VA" mfr = "Mustek" model = "PowerMust 600VA Plus" i have the next in log: /usr/syno/etc/rc.sysv$ sh ups-usb.sh restart Network UPS Tools - Richcomm dry-contact to USB driver 0.04 (SDS6-0-8445-factory-repack-8445-160817) Warning: This is an experimental driver. Some features may not function correctly. ups-usb.sh restart invoked. Stop UPS Daemon Can't open /var/state/ups/blazer_usb-ttyUSB0.pid: No such file or directory Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Network UPS Tools - Megatec/Q1 protocol USB driver 0.11 (SDS6-0-8445-factory-repack-8445-160817) Fatal error: 'mfr' is not a valid variable name for this driver. Look in the man page or call this driver with -h for a list of valid variable names and flags. Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 The UPS is connected. driver=[] Start UPS Server fopen /var/state/ups/upsd.pid: No such file or directory listening on ::1 port 3493 listening on 127.0.0.1 port 3493 listening on fe80::211:32ff:fe14:4dc1 port 3493 listening on 192.168.1.4 port 3493 Can't connect to UPS [PowerMust] (blazer_usb-PowerMust): No such file or directory /usr/share/cmdvartab not found - disabling descriptions Quote Link to comment Share on other sites More sharing options...
shrabok Posted February 19, 2017 Share #3 Posted February 19, 2017 I don't think you have a supported UPS https://www.synology.com/en-us/compatib ... mode=false Quote Link to comment Share on other sites More sharing options...
aleksey_z Posted February 19, 2017 Author Share #4 Posted February 19, 2017 I don't think you have a supported UPShttps://www.synology.com/en-us/compatib ... mode=false Yes, I know that my old UPS Mustek 600 with rs232, not in the list of compatible. But reading the forum, I think it can be connected to the server. I installed blazer_ser driver (using opkg). Now with these settings in ups.conf [ups] driver = blazer_ser port = /dev/ttyUSB0 desc = "PowerMust 600 USB" vendorid = 0x06DA productid = 0x0003 mfr = Mustek model = PowerMust 600VA Plus I get: /usr/syno/etc/rc.sysv$ sh ups-usb.sh restart ups-usb.sh restart invoked. Stop UPS Daemon Can't open /var/state/ups/blazer_ser-ttyUSB0.pid: No such file or directory Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Supported UPS detected with megatec protocol Vendor information unavailable No values provided for battery high/low voltages in ups.conf Using 'guestimation' (low: 10.400000, high: 13.000000)! Battery runtime will not be calculated (runtimecal not set) Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 The UPS is connected. driver=[] Start UPS Server fopen /var/state/ups/upsd.pid: No such file or directory listening on ::1 port 3493 listening on 127.0.0.1 port 3493 listening on fe80::211:32ff:fe14:4dc1 port 3493 listening on 192.168.1.4 port 3493 Can't connect to UPS [ups] (blazer_ser-ups): No such file or directory /usr/share/cmdvartab not found - disabling descriptions or after restart /usr/syno/etc/rc.sysv sh ups-usb.sh restart /usr/syno/etc/rc.sysv$ sh ups-usb.sh restart ups-usb.sh restart invoked. Stop UPS Daemon Can't open /var/state/ups/blazer_ser-ttyUSB0.pid: No such file or directory Network UPS Tools upsd SDS6-0-8445-factory-repack-8445-160817 Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Stop UPS timeout, Force stop UPS Can't open /var/state/ups/blazer_ser-ttyUSB0.pid: No such file or directory Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 Stop UPS timeout, Force stop UPS Can't open /var/state/ups/blazer_ser-ttyUSB0.pid: No such file or directory Network UPS Tools - UPS driver controller SDS6-0-8445-factory-repack-8445-160817 UPS driver alive UPS driver alive UPS driver alive Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.