Jump to content
XPEnology Community

Drivers requests for DSM 5.2


Recommended Posts

Hello,

 

I am running DSM 4.3-3810 - v1.1 Beta 4. I would like to try Beta 5 but I don't want to loose my configuration. Is there a way to get the new .pat file over to my Beta 4 installation?

 

TIA,

 

 

 

 

Update:

Followed procedure from viewtopic.php?f=2&t=1086&p=8501&hilit=downgrade+to+4.2#p8501 to trick the system to do a migration to DSM 4.3-3810 - v1.1 Beta 5

 

No loss of data but some loss of configuration.

Link to comment
Share on other sites

Hello,

 

i am currently testing XPEnology latest BEAT (5) in my HP ML310e G8.

So far everything seems to be fine, also the M1015 HBA (LSI IT Mode flashed) is working.

 

Unfortunately i want to use my 10G NIC (HP NC523SFP) which doesn't show up in WebGUI.

 

Here is the link to HP's driver page:

http://h20566.www2.hp.com/portal/site/h ... .199480143

http://www8.hp.com/us/en/products/adapt ... b=features

 

Thank You in advance

 

BR

snoopy78

Link to comment
Share on other sites

Unfortunately i want to use my 10G NIC (HP NC523SFP) which doesn't show up in WebGUI.

 

Link : http://xpenology.trantor.be/beta/qlcnic.ko

Copy the module to /lib/modules and insmod it :wink:

I'm curious about performance with this ^^

 

Will be included in next repack.

 

Mellanox ConnectX® InfiniBand (MHGH28-XTC) 10GB ethernet 30€ dual port card on ebay. Cheap 10 GB ethernet :smile:

 

Link : http://xpenology.trantor.be/beta/mellanox.7z

 

Same as above, copy .ko files to /lib/modules and insmod mlx4_core.ko then mlx4_en.ko

Link to comment
Share on other sites

Hi Trantor,

 

i just found the cause...

 

the NIC has 2x 10GBe interfaces and my connection was the 2nd one (should be eth3) but only the 1st port (eth2) was enabled... now i switched from eth3 to eth2 and got connection.

 

Maybe in future releases you can add the 2nd port, or make an install not..:wink:

 

going to test now and then report to you :grin:

 

THX & BR

snoopy78

Link to comment
Share on other sites

Hi Trantor,

 

here are the 1st tests.. need to check and do more testing.. :wink:

 

i think my main pc is the limitting factor as the 10gbe card is pcix8 and the slot is pcix4...

NetIO

"

C:\NetIO\bin>win32-i386.exe -t 192.168.0.110

 

NETIO - Network Throughput Benchmark, Version 1.32

© 1997-2012 Kai Uwe Rommel

 

TCP connection established.

Packet size 1k bytes: 157.76 MByte/s Tx, 242.42 MByte/s Rx.

Packet size 2k bytes: 247.35 MByte/s Tx, 259.62 MByte/s Rx.

Packet size 4k bytes: 431.31 MByte/s Tx, 256.67 MByte/s Rx.

Packet size 8k bytes: 436.57 MByte/s Tx, 253.71 MByte/s Rx.

Packet size 16k bytes: 455.37 MByte/s Tx, 246.44 MByte/s Rx.

Packet size 32k bytes: 458.36 MByte/s Tx, 251.32 MByte/s Rx.

Done.

 

 

C:\NetIO\bin>win32-i386.exe -t 192.168.0.110

 

NETIO - Network Throughput Benchmark, Version 1.32

© 1997-2012 Kai Uwe Rommel

 

TCP connection established.

Packet size 1k bytes: 152.42 MByte/s Tx, 220.70 MByte/s Rx.

Packet size 2k bytes: 227.04 MByte/s Tx, 244.57 MByte/s Rx.

Packet size 4k bytes: 444.78 MByte/s Tx, 260.61 MByte/s Rx.

Packet size 8k bytes: 462.11 MByte/s Tx, 257.50 MByte/s Rx.

Packet size 16k bytes: 403.26 MByte/s Tx, 229.40 MByte/s Rx.

Packet size 32k bytes: 474.31 MByte/s Tx, 248.82 MByte/s Rx.

Done.

 

 

C:\NetIO\bin>

 

 

C:\NetIO\bin>

"

 

Update @ Trantor

BOTH 10G ports are now available and working :grin::grin::grin:

 

br

snoopy78

3xSSD-SHR_MTU_9000.jpg.c79d66622b026acd8e83c706e12f94f2.jpg

3xSSD-SHR_MTU_1500.jpg.7a22de9914e9206405bb40db45f5b19f.jpg

volume_manager.jpg.a06e3e751765e831c532bb2b2d90a456.jpg

Link to comment
Share on other sites

Hello,

 

are the drivers for the N54L onboard eSata Port Multiplier already integrated or is a PCI-E eSata with another Port Multiplier supported Chipset necessary?

 

I have a N54L with Xpenology DSM4.3 and BIOS Mod 0.41 but onboard eSata Port Multiplier is not working with my Lian Li EX-503 eSata enclosure (JMB393 Chipset).

Link to comment
Share on other sites

Hello,

 

I was wondering, is it possible that the DSM 5 beta supports an onboard wifi PCEe card (ac)? Can I use the wifi card instead of LAN cable?

Board is an ASROCK Z87E-ITX (http://www.asrock.com/mb/Intel/Z87E-ITX/)

 

Wifi PCIe model here:

https://wikidevi.com/wiki/Broadcom_BCM94352HMB

 

Linux driver (64/bit) for the PCIe card here:

http://www.broadcom.com/support/802.11/linux_sta.php

Link to comment
Share on other sites

Hi Trantor,

 

First off, massive thanks for the whole build really. Using a HP N54L and DSM has made one hell of a difference to the way I work at home, so much so I'm slowly by surely fazing out all MS crap in my house.

 

Anyway, rather than ask you to compile drivers for me for a part I haven't bought yet, I wondered if there was already a PCI SATA expansion card set of drivers available? I have an ICY dock in which I'd like to add an additional 6 2.5" drives, that can only be achieved by adding an expansion card.

 

Also, again so as to not trouble you, I Google'd adding drivers to a Synology and found the below. Is it really that easy? Because if so I'm happy to do this myself, and I'm sure armed with this info most others are.

 

For the people intersted in how i got it compiled. first we need to get the package manager ipkg to work:
INSTALLING IPKG
-open dsm package center and add the package source http://packages.quadrat4.de
-refresh 
-install bootstrap installer to get ipkg.
-reboot,wait until the beep check that the nas is still fine
-enable ssh client in the dsm by clicking on terminal and check ssh.
-use http://www.putty.org/ to ssh on port 22 into your nas.
-login as 'root' with your admin password defined in dsm.

GET BUILD ENVIRONMENT
now you are ready to get the build environment ready:
-execute 'ipkg update'(update should be succefull)
-'ipkg install make' to get the buildtool make
-'ipkg install gcc' to get the c compiler gcc

DOWNLOAD AND COMPILE SOURCES
-download your source files for your hardware.
-put it somewhere on your nas.
-via putty 'cd /volume1/'
-now make sure your ssh location is in the folder where Makefile is located
-execute 'make'

Your driver is now compiled for the Synology. 

Link to comment
Share on other sites

Hi Trantor,

 

Excellent work with XPEnology project! Loving it.

I wanted to ask if you could add the driver for RocketRAID 2640x4 controller?

 

RocketRAID 2640x4 controller driver location

 

I tried using the DSM 5.0 beta build that you compiled with the RocketRAID controller, however my 4 HDDs connected to the controller were not being recognized by DSM. I am using Intel S5000XVN MB. When I disconnect the HDDs from the RocketRAID controller and reconnect to the MB, DSM recognizes the HDD (well except one, but that's another story, troubleshooting for another night :-/ )

 

Thoughts, anyone?

Thank you.

 

~Atrio

Link to comment
Share on other sites

Hi,

I would like to buy this mobo :

http://www.servershop-bayern.de/index.p ... &info=9584

http://www.servethehome.com/Server-deta ... rm-review/

 

This hardware is very new.

the SATA controllers are : Intel ® C2750 , Marvell SE9172 , Marvell SE9230

the network controllers are : dual Intel i210 gigabit Ethernet controller , 1 LAN port for the Aspeed AST2300 BMC’s onboard IPMI 2.0 functionality

 

Does this mobo work with xpenology ?

Link to comment
Share on other sites

This is an updated beta which include several updates/fixes.

 

Before doing anything, backup your data.

No warranty for any damages, loss of data or anything else.

 

Link : http://xpenology.trantor.be/beta/

 

Just a little update, nothing amazing.

 

Use .pat file from beta5 to install XPEnology.

Two version of synoboot : standard and hba (with scsi/sas drivers)

 

 

Changelog:

v6 (09/02/2014)

- Fix grub error 17 (introduced in beta5)
- Add Mellanox Technologies 10Gbit Ethernet support
- Add QLOGIC QLCNIC 1/10Gb Converged Ethernet support
- Add RocketRAID 2640x4 support (rr26xx driver)

v5 (20/01/2014)

- Add VIA CPU support (CENTAUR)
- Update synobios.ko (by k3dt ; fix "buzzer stop button pressed" warning)
- Add Brocade 1010/1020 10Gb support
- iSCSI (block level) works in IET mode (change lio to iet in synoinfo.cfg)
- iSCSI (regular) works in LIO mode
- NFS working
- CIFS mount point working
- Include bootstrap ipkg setup script (/root.profile is already modified) : after setup just log to ssh and type :
sh syno-i686-bootstrap_1.2-7_i686.xsh
reboot, log again to ssh and type
ipkg update


v4 (29/12/2013)

- You can now install DSM on drives connected to a SCSI/SAS controller
- Fix the volume "broken" issue when DSM is installed on a SCSI/SAS controller
- Fix NFS support
- Update megaraid_sas driver to the latest version
- Modify the way XPEnology's modules are loaded in ramdisk
- Include modules from previous beta
- Add PS2 keyboard support

v3 (21/12/2013)

- Add more drivers for KVM / virtio / virtualization support
- Add patched r8169 driver (realtek chips which are not working with the r8168 driver will work with this one)
- Add latest version of sk98lin driver (Marvell Yukon / SysKonnect SK-98xx/SK-95xx support)
- Update Broadcom bnx2 driver to latest version


v2 (05/12/2013)

- AX88179 Gigabit Ethernet USB 3.0
- Latest driver version for RocketRAID 3xxx/4xxx Controller
- Latest (aacraid) driver version for Adaptec
- Support XFS filesystem (no idea if DSM will automount this)


v1

- Update synobios.ko (by k3dt ; fix "buzzer stop button pressed" warning)


SCSI
----

Highpoint Rocketraid 2720SGL
LSI mpt2sas v17
Adaptec aacraid
Intel C600 Series Chipset SAS


NETWORK
-------

3Com 3c590/3c900, 3cr990
Alteon AceNIC/3Com 3C985/NetGear GA620
QLogic QLA3XXX
SiS 900/7016 SiS190/SiS191


USB
---

USB to serial / Prolific 2303 driver


PATA
----

ATI PATA (PATA_ATIIXP)
AMD/NVidia PATA (PATA_AMD)
CMD64x PATA (PATA_CMD64X)
JMicron PATA (PATA_JMICRON)
Marvell PATA (PATA_MARVELL)
Promise PATA 2027x (PATA_PDC2027X)
Intel SCH PATA (PATA_SCH)
CMD / Silicon Image 680 PATA (PATA_SIL680)
SiS PATA (PATA_SIS)
VIA PATA (PATA_VIA)
Winbond SL82C105 PATA (PATA_WINBOND)
Legacy PATA support (PATA_LEGACY)

Link to comment
Share on other sites

v6 (09/02/2014)

- Fix grub error 17 (introduced in beta5)

 

I'm using Beta 5 without any problems until now. Can you explain, under which condistions the mentioned grub error 17 occurs?

I just want to update if it is really necessary.

 

Thx for your great work!

Link to comment
Share on other sites

with synoboot pre v1.1 v3

 

driver for ax8879 is not present

driver fro rt28000usb doesn't work :sad:

 

I will add all modules in next beta.

 

Regarding WiFi driver, how will I know which wifi driver I will copy to modules. Im using 4.3

My motherboard is zotac h87 with an onboard wifi. Also can you have driver for bluetooth.

 

Boot on ubuntu livecd to find out which modules you need.

 

 

 

See next post about SCSi/SAS controllers

 

 

 

Hi Trantor,

 

I already know my wifi driver that is iwlwifi.ko

I have already copied this to /lib/modules/

 

but when i try to execute this command : insmod iwlwifi.ko

i have this error: "insmod: can't insert 'iwlwifi.ko': unknown symbol in module, or unknown parameter"

 

What could be the problem and how will i resolve it?

 

By the way im using DSM5.0 Beta.

 

Thank you.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...